I’ve been seeing a lot of maker sites featuring both Osmo Polyx and Rubio Monocoat finishes (hardwax oils).  They seem to go nicely with the live edge tables that are so popular today.  I imagine these companies are doing a good job reaching out to the makers because it seems like an effective effort.  I’ve also seen some examples of Odie’s Oil and and it looks like a similar product only with less marketing flair.  I was on the fence and was leaning toward Rubio, only because it seemed like more makers were featuring it.   Then I ran across this series of 4 videos by Blacktail Studio that test out hardwax finishes each of 4 different ways.
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.

Thinking about starting a crafts or DIY business? Take a look at these creative ideas using pallets, which have become very popular. One of the reasons many enjoy creating DIY ideas into DIY projects with pallets is there are so many different type of items and decorations that can be made from this rustic wood. Pallets are simply leftover wood and using them is a very eco-friendly and green thing to do. If you choose to make these crafts to sell, you’ll be pleased to discover that many pallet crafts can be created over a weekend. So give DIY pallet projects a try, there are so many here to enjoy! Happy Building and Selling!
There are and they are considerably cheaper. I found a pair of glue brushes on Amazon for less than half the price of a singles dedicated glue brush. I tested them out on a recent gluing and they work well for spreading glue and getting it into dovetails and mortises. When you are done you can either run the brush underwater to clean it or wait until the glue dries the pluck it off the bristles with a few easy pulls. The glue comes right off the silicone bristles.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
As a gardener/homesteader, and setting aside basic firewood tools (chain and bow saws, hatchet, axe, maul, sledgehammer and wedges), the most important woodworking tool I possess is the drawknife. This enables one to quickly and efficiently peel bark off of saplings and poles (which alone increases their durability outdoors, and is essential to prepare them for other uses), and is also good for rough shaping work....more accurate than a hatchet, and quicker than a chisel in many cases. I probably use my drawknife about as often as any of the basic carpenter's tools like a crosscut saw or an electric drill. 

Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.

About Youtuber Have you ever considered woodworking as a hobby but didn't where to begin? Tune in for this video series from the editors of Fine Woodworking magazine, and we'll guide you through the process. From choosing your first tools to setting up a workspace to completing your first woodworking projects, you'll discover just how easy it is to get started in woodworking.
Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  
The second big tool you need is a saw. There are many types of saws, and this can be the trickiest part of setting up a shop on a budget. As a beginner, you'll likely be using woodworking books, magazines and websites for instruction and inspiration. Unfortunately, most of these sources consider a table saw a beginner tool. For those of us on a budget, or with little space, a table saw may not be an option. They cost several hundred dollars to start, and take up several square feet of floor space. Instead, look for a good circular saw that allows you to adjust the depth and angle of cut. It's also nice to have a laser to help guide the cuts. You can get a decent circular saw for around $100.
Ready for fall? Fall is one of my favorite seasons (hello cute boots and cozy sweaters!), plus I love watching the leaves turn gorgeous colors. You can bring a bit of that colorful nature indoors this fall with some simple fall wood crafts. Just grab a few scraps of wood, some fallen branches, or some wood slices, and whip up these adorable fall crafts in no time!
If you want to do any amount of bowl carving or other types of carving that will require removal of large amounts of stock, I can't recommend an angle grinder and chainsaw-tooth wheel in place of the abrasive wheel. I've used the Arbortech brand, but there are a few different brands and style available. I'm sure you could buy a used grinder for $20 or so.
Raw material is a concept. A concept that we describe as any material that has yet to find its final home. It is a material that is en route to becoming something interesting, creative and more permanent in the world. If it has yet to be worked and transformed to create a unique piece of woodworking or artisan craftsmanship, then it is still raw to us.

The next hand tool every woodworker should have is a nail set. In fact, you should have several sizes. They look like awls, and you use them to drive nail heads into the wood so they are flush or right below the surface. This allows you to fill the holes and prepare for staining or painting. The nail setter will usually have either a convex or concave surface to grip the nail better and keep it from sliding off and marring the wood.


A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57050 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ...  More + Product Details Close
In my shop I use a large number of Jorgenson F-clamps. I use many of the small clamps, the most useful being the 12" version. Large F-clamps are essential for cinching down parts on bending forms. I also like aluminum bar clamps because they are much lighter than steel clamps, and therefore less likely to damage a carcase should you bang into the wood dur­ing a glue-up.
Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.
On the 100/300 grit combo stone: absolutely, positively NO – and I’m a woodworker by training who sees sharpening of tools as a means to an end and not as a religion. DMT bench stones are soooo cheap in the US (they cost as much as 3 times as much in ROW) that you should not waste (expensive) time with Chinese carborundum stones or EZ-Lap …err … junk.
Woodworking is a highly visual craft. There’s just something photogenic about lumber getting cut to size, dry-fit, glued or tacked together, and finally sanded down and finished into a beautiful piece of furniture. Even if you’re not a woodworker yourself, watching high-quality woodworking videos is a great way to learn about how stuff gets made, and who knows, you might even realize you want to make something yourself.

The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.


Not many YouTube woodworking channels are run by guys who also happen to have PhD’s in medicinal chemistry, but this one is. Brian Grella’s channel offers a mix between more atmospheric videos that aren’t heavy on explanations (as the one shown above), and ones that are firmly in how-to territory, like this one for making a beautiful wooden bowl using nothing but a router and a drill press (no lathe required):
If you’re woodworking as a hobby, you already know that it can get very expensive. Saving money by not buying redundant tools is one way to keep it slightly more affordable. If you’re doing this as a business like I am, then every dollar saved is another dollar you can invest in your business. If you have other money saving tips, please feel free to share them!
I find, as others have noted, that braces are pretty easy to find, and bits for them in decent condition harder. I too tend to buy them whenever I see them. There are a number of varieties of brace, and some meaningful differences in them. Pay attention to the design of the chuck, and to whether the brace is ratcheting, or not. They're all good, but some differences in best application.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
Carpenters Builders Pencils 13pc Joiners Sharpener Soft-lead oval-section carpenters pencils for marking timber, brick, stone and other building materials. Draws thick or thin lines on both rough and smooth surfaces. Oval-shaped length means pencils do not roll away when placed on inclined surfaces. Includes 12 pencils and a sharpener. Pencils supplied are in BLUE.
Hobbies on a Budget reader Rob sent me this tip: Recycle wood for small projects. I have gotten a lot a usable wood from old mattress frames, pallets, panel doors and even a piano. A little bit of destruction work and some cleanup and you can get a ton of useable wood. The best part is that the wood stays out of the landfill. Cost for reused wood? FREE

@jayemel: tempered glass works perfectly, as the (theoretical) fluctuations in flatness as a result of inner stress are several orders of magnitude smaller than the significant variations of thickness of your sandpaper. Unless you want to reflect the light of distant galaxies off the bevel of your chisel and measure their red-shift, you will be fine (and safer) to use tempered glass.
In the rough is referring to the wood at its earliest stage in the woodworking process. When the wood is initially milled from very large logs into more workable slabs, it is then kiln-dried to reduce the moisture content. At this point, the wood is able to be machine planed to a finer finish or left in its more natural state. The wood, in its more natural state, reveals the unique tooth and saw marks from the mill, creating a more rustic look and feel in the wood.
One purchase that did work out in my favor this year was a bandsaw. I found an old, built in 1946, 14" Delta bandsaw w/ riser block in good condition for a steal at $150. I had a couple months of free spend saved up, and my wife threw in the rest of the money and considered it my birthday gift. Attached to the saw's base was an old Stanley 77 dowel maker the seller gave me with the saw since it was attached to the base when he got the saw. I was able to sell it on ebay for just shy of $300. I actually made money on that deal, and the money from the sale has allowed me to buy blades and upgrades for the bandsaw, as well as the parts and materials I need to build the router table I'm in the process of building. Was nice to get that - otherwise it would be months before I'd be able to purchase some of those things!
Not many YouTube woodworking channels are run by guys who also happen to have PhD’s in medicinal chemistry, but this one is. Brian Grella’s channel offers a mix between more atmospheric videos that aren’t heavy on explanations (as the one shown above), and ones that are firmly in how-to territory, like this one for making a beautiful wooden bowl using nothing but a router and a drill press (no lathe required):
When I built my shop I opted to buy a much higher quality miter saw and table saw than I truly needed at the time.  It ate up a ton of my budget and forced me to put off adding the tools that would allow me to buy cheaper stock for 2-3 years.  During that time my savings buying rough cut lumber would have probably paid for the upgraded equipment I started out with.  

"Woodworker's Supply, Inc. failed to properly investigate these complaints and failed to protect Ms. [Teresa] Logsdon from illegal sexual harassment, and gender discrimination in the workplace," according to the complaint filed by her attorney Wendy Owens of Casper in July. "Ultimately, Ms. Logsdon had no choice but to give notice of resignation to protect herself."
×