Fine Woodworking Tools and Supplies at Highland Woodworking – make us your woodworking tool supply source. Woodworking Hand Tools are one of our passions at Highland Woodworking so we sell the very best hand tool brands in production today. Handmade, high quality hand tool lines such as Auriou Rasps, Barr Forged Tools, Gransfors Axes, Lie Nielsen Tool Works, Woodpeckers Precision Tools and numerous other fine hand tool makers. We love fine Woodworking Power Tools too, so we sell Festool Power Tools and SawStop - the best power tool brands for woodworking. We've been offering fine woodworking tools and education since 1978, keeping woodworkers informed about the best woodworking tools, tips & techniques along the way. Purchases are backed by Highland Woodworking's 60-day money back guarantee, so you can shop us with confidence for high quality woodworking tools, equipment & supplies.
I’m going to find a different piece of metal, and I’ll post a video of the working track when it’s done. I bet some of you are coming to expect failure from this blog. I warned you in the beginning that I’m new to this. I’m trying to share my experience from both my successes and my failures. It just so happens that I have a lot more failures so far. 

About Youtuber Here you will find everything from money saving tips, woodworking projects, jigs and completely wild contraptions. I have been building and designing since I was old enough to swing a hammer. With a mind for out of the box thinking and an unusual mix of artfull design and engineering interest, you never know whats going to happen next.
Saws (I'm not a fan of Japanese saws, but you can buy good new ones pretty cheap.  ) - 1 crosscut handsaw (can be a Stanley "Sharktooth" toolbox saw from Home Depot or Lowes $15).  1 rip handsaw (used ones can be found at Antique stores for $20 or less.  Try to find one that is fairly sharp to start with).  Dovetail saw (Crown has a decent gent's saw for around $25 or get the Lee Valley Veritas Dovetail saw for around $70, Highland Woodworking carries both).  A crosscut backsaw and small miterbox is also handy to have, I can't give you a recoomendation for inexpensive ones though.
Wow that’s a lot of assuming and supposing :) no shop right? no tools right? a place to work and tools for under 3K right? . This ones easy buy a pocket knife, set in your living room and whittle . So far you have $20 spent for a pocket knife. You might need another $200 for a decent vacuum to clean up all the shavings you made in your living room.
The level of sophistication in a $250 shop is significantly less than a $2,500 shop.  But keep in mind even a $2,500 budget is entry level.  Acquiring a shop full of the perfect tools for each and every job takes a life time.  But that doesn't mean that producing quality work takes a lifetime.  One of the most enjoyable aspects of this hobby is the constant need to solve problems in order to produce good work.
To get the most out of your router, you are going to want a router table.  You may find yourself asking if you really need one - if you do, check this post out.​  It's one of those purchases that you won't truly understand how valuable it is until you have one.  Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150).  If you want to see our favorite tables along with write-ups, check them out here.

For woodworking entertainment and inspiration be sure to checkout our Woodworking Video Series "The Highland Woodworker". Improve your woodworking skills and learn more about the use of woodworking tools with free online woodworking materials in the Woodworking Library. At Highland Woodworking you get more than fine woodworking tools...you get fine tool tips too!


About Youtuber Woodworking is my passion and I there is nothing I won't try to build, fix, or improve on my own. I got into woodworking and the passion has completely consumed me. Becoming a great woodworker and do it yourself-er is about finding the right information and creative solutions with the materials and skill sets available to you. I eagerly look forward to showing you how I accomplish my projects.

My Husband is Shane’s Hobby Shop and he already is on your list, so you see, even tho I do have other diy items attached, woodworking is most definitely an ongoing part of my show. I only have one official episode out, but this week I will be posting episode number 2…this will feature PART 2 Of my Cracker Platter that I built with Shane, as well as my OWN Version of a Wood Conditioner that I have created that I will be using on Shanes Potato Bin that he built and I will be going over the ingredients used, the why behind each ingredient, and WHY it was chosen to be used on wood to begin with. Should be an interesting show. I will also be doing a show on Homemade Southern Gumbo…so you see, a good combination, but definitely woodworking centered. Thanks for adding my Channel.


With the right tools and materials, what you build is only limited by your imagination and creativity. So why not have a little fun with the kids and teach them something at the same time? Our woodworker tools and woodworking supplies will help you put together an easy birdhouse, squirrel feeder or butterfly house. The kids will love to use our paint samples to add their creative touch, and will enjoy displaying the finished product in the backyard.
I place the band saw first in my order of purchases, because I consider it the heart of the shop. Band saws are very safe tools for ripping, re-sawing, cutting curves and more because all of the force is downward, virtually eliminating any chance of unexpected kickbacks. I wanted a saw that had a strong back, dynamically balanced cast iron wheels for smooth operation and flywheel effect, 12" depth of cut, good dust extraction design, a large table and a solid fence. After shopping around, I settled on the General International Model 90-170 14" saw. It is very smooth, comes with an Excalibur fence, and it is light enough (133kg) to move into your basement without crushing someone.
The variety of colors and tones, textures, and grain patterns seen in most hardwoods create some of the most beautiful and unique furniture in the world. Hardwoods are generally more expensive than softwoods, but the finished look can be well worth the additional cost. Hardwoods are often more durable and are therefore generally recommended for tabletops and countertops. Many hardwoods do not need to be stained, but rather hand-finished with natural oils to enhance their beautiful grain and texture.
I went out and bought a dovetail pull saw for some of the finer cuts that I needed to make. I’m sure I’ve used this a few times on previous blog posts. It is great for the smaller cuts, and I’ve even used it to cut some larger pieces when my bigger saw didn’t fit. The combination of the dovetail pull saw and the push saw works fine, and isn’t too terribly expensive, but I’ve found something even cheaper that works just as well.
The circular saw is pretty much the first tool I grab for any project. You can use it for both rough cutting your lumber to get started on a project or making finish cuts before final assembly of your project. You can use it to make half lap joints and a variety of other joinery methods. While a table saw or stationary miter saw might make a certain task easier, it is hard to beat the cost, portability, and versatility of a circular saw. While most of these come with a blade, here is a good all-around blade that I use.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
The best advise I can give you is to get and read the book "Hand Tool Essentials" by the staff of Popular Woodworking before buying any tools.  It is sort of an inexpensive crash course in hand tools.  Chris Schwarz's book "The Anachrist's Toolchest" is another good source of information on handtools that I found to be a fun read.  Use the internet to learn all you can about a tool before buying.  The tools you need are dictated by what you want to build.
Not many YouTube woodworking channels are run by guys who also happen to have PhD’s in medicinal chemistry, but this one is. Brian Grella’s channel offers a mix between more atmospheric videos that aren’t heavy on explanations (as the one shown above), and ones that are firmly in how-to territory, like this one for making a beautiful wooden bowl using nothing but a router and a drill press (no lathe required):

These YouTube woodworking how to videos are created to share experience. These videos are specifically intended for anyone who desires to learn and enjoy the craft of woodworking. Some woodworkers and carpenters may find the woodworking projects  to be simple, fun, and exciting. Other woodworkers and hobbyists may find an online project that is a challenge.  Either way, my hope is that when you watch video clips, you will think, ask great questions, and learn.
Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.
Raw material is a concept. A concept that we describe as any material that has yet to find its final home. It is a material that is en route to becoming something interesting, creative and more permanent in the world. If it has yet to be worked and transformed to create a unique piece of woodworking or artisan craftsmanship, then it is still raw to us.
Turn leftover wood or old pieces of furniture into DIY reclaimed wood projects! Wood is one of my favorite materials to work with. The possibilities are endless and they give such a homey and cozy feel to any rustic home. My husband, Dave, and I sometimes even go the extra mile and carve our initials on a little spot. It’s our own way of making our DIY project even more personal! Here’s a list of some of our favorite DIY reclaimed wood projects!   
You can create a beautiful coffee table by simple stacking logs together. Line the logs end up and create a circle whatever size you need. Then just tie them all together with rope or twine to keep your coffee table secure. You do need to make sure that the logs are the same height and you may want to sand the tops down just a bit to make them smooth.
Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.
×