One subject that a woodworker must always consider when building a project is how seasonal moisture and temperature fluctuations will cause expansion and contraction of the wood stock in the assembled project. For instance, if you've ever experienced a drawer that sticks only in the winter time, you've experienced seasonal movement of wood. Since each wood species is affected by these temperature and moisture fluctuations, you'll need to know a bit about the climate where the project will be used, and how your chosen wood stock is affected by the climate changes. Again, your local woodworking supplier can be a great resource for answering these types of questions in your area.
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
Clamps are absolutely essential for most woodworking projects. This is why I’ve included clamps in the list of tools that beginners need when starting woodworking on a budget. However, I often run into situations where I don’t have enough or the right kinds of clamps. Today I’m going to share a few ways that I’ve gotten by without just going out and buying more clamps.
Birch comes in two varieties: yellow and white. Yellow birch is a pale yellow-to-white wood with reddish-brown heartwood, whereas white birch has a whiter color that resembles maple. Birch is readily available and less expensive than many other hardwoods. Birch is stable and easy to work with. However, it’s hard to stain because it can get blotchy, so it is generally preferred to paint Birch.
Do you enjoy woodworking? Do you have a budget that you have set aside just for your woodworking? If you are not a millionaire, than more than likely you will have some sort of a budget. Let me give you a little insight into why you are here and what you will find on this site. Do you enjoy woodworking as a hobby, part-time job or side job, or a full time job? Or maybe you are wanting to turn your hobby into a full time job. If that sounds like you than your in the right place.
Softwoods are often softer and more delicate woods in general, as the name would suggest, but aren’t necessarily always weaker than hardwoods. Although, they are generally less dense and not as durable as Hardwoods, which grow at a much slower rate than softwoods creating a denser and stronger grain in the wood. Softwoods come from coniferous (or gymnosperm) trees such as Cedar, Hemlock and Pine and lean towards a yellow to reddish tone by nature. Hardwoods come from angiosperm (seed producing) trees such as Oak, Cherry, Maple and Walnut and are generally darker toned woods. Softwoods tend to be less expensive than hardwoods, as they grow much more quickly and can be milled at a faster rate. While hardwoods are generally more expensive, the durability, strength and overall look is often worth the additional cost depending on your project needs.
If you have wood pallets just lying around the yard, put them to use by turning them into a great mud room bench. This bench would look fabulous on the deck or just inside the door, wherever you want to put it. When you finish putting it all together, just sand and stain it whatever color you want and you have a beautiful bench that cost you very little to create.
We've written about routers on the site before and my favorite is the Bosch 1617. It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table. On top of that, it comes with a plunge base which makes it significantly easier to use handheld. The package clocks in at ~$190.
After years of digging down under router tables, lifting the entire unit up to change bits, and then fighting to get the plate flush again in the table, I chose to spend the money to purchase a router table, fence, and lift system. I did a thorough review of these systems, and chose the Canadian made Jessem Rout-R-Lift II kit. The system comes with a solid steel stand, a phenolic table, an adjustable extruded aluminum fence, and their base model lift system. For budget reasons, I did not choose the hefty Mast-R-Lift, but I am quite happy with the lighter Rout-R-Lift II. It will last me a couple of lifetimes, so it is the right system at the right price for me in my one-man shop. Hats off to Jessem for making a great lift at a very reasonable price in the middle of a tough economy. The table is durable, and flat. The direct drive lift is smooth and precise. I mated the lift system to a mid-sized model 690 Porter Cable router, which has a fixed speed, and enough power to do anything I need. The Jessem system uses a bayonet type mount for the table inserts, a nice touch that makes swapping the table insert quick and simple. As with all my machines, the router table is connected with the supplied dust port to my shop dust collection system with automated switching.
Even if you don’t live in a rustic log cabin, you can give your home a great cabin look by simply planking one or more walls. This is a relatively easy project that will add beauty and value to any home. Just choose the wall that you want to change, and add wooden planks which you can pick up at most home improvement stores for very little. Then stain if you want and you have a lovely cabin type wall
We’ve already done rope, and now we’re on to another rustic material we love: wood! It’s as basic of a material as clay and is constantly reinvented by DIYers, crafters, artists, hackers, and carpenters. To get inspired to create our own batch of cool wooden objects, we turned to our favorite fellow makers to see what projects they’ve come up with. Scroll down for our top DIY wood project picks.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected. We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.