I could not consider a 12" jointer, given that the equipment had to be moved down the stairs to my basement, and the cost would blow my budget. What I wanted in an 8" jointer was true tables, a fence that is solid and easy to adjust, a cut depth gauge that is reliable, and long tables that aid in flattening longer bowed planks. I have found that the Taiwanese tools have come a long way in the past 20 years. I purchased the King KC-80FX 8-inch jointer, with lever adjust parallelogram tables. The system arrived in a good state of tune, and the well-written manual includes a full parts list and exploded parts diagrams. The tables were extremely heavy; more about getting things down the stairs later. The jointer is reasonably priced, it runs smoothly and it is well made.
If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.
If you’re woodworking as a hobby, you already know that it can get very expensive. Saving money by not buying redundant tools is one way to keep it slightly more affordable. If you’re doing this as a business like I am, then every dollar saved is another dollar you can invest in your business. If you have other money saving tips, please feel free to share them!
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking. These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email email@example.com and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence.
I just do it. Lol. Most of my projects are for my wife so its easier to scrape money together then listen to complaints about them not getting done! Seriously though, its tough. I have two expensive hobbies......woodworking and bass fishing, latter of the two being the worst. I reserve all my side work money for the two. One thing that helps is owning our own saw mill, lumber is basically free other then time.
Man, do I ever know about the "pre-buyers remorse"! My fiancé is a self proclaimed "cheapskate"(her language is a bit more coarse), but when it comes to my shop, she's all for me spending. I always end up being the one to pump the brakes, as I have a history of being TERRIBLE with money(@ 21, I was making close to 6 figures with no post-secondary education, and at 31, I still have less than $5,000 in the bank), while she pushes me to get "whatever I need". Of course, we all know that the line between want and need is pretty blurry. I agree with some of the other posts; I keep all of my expenses logged, and try to churn out money-makers to chip away at the red, always hoping to reach the black. So far, I'm still seeing red, but as my shop continues to flesh-out and my skill set grows, profit begins to sound more and more feasible all the time. Of course, I'm not really trying to make money. I just want to buy bigger and better equipment and supplies!
Now, I’m not crazy rich or anything. I know that’s still a lot of money, but you will be able to make SO many things with just these five tools you seriously won’t believe it. And if you are just starting out, just buy one tool and try it out. You’ll be surprised how much you can make with just a jigsaw, hammer, nails and a screwdriver. I made tons of stuff! All you have to do is get started…where there is a will there is a way. 🙂
This is known as the “Scary Sharp” method and I first learned of it on Usenet back in the day. I’ve had pretty good luck only going up to 2000 grit automotive paper. That stuff is commonly available near the spraypaint at Wally-world. At this grit, I can easily shave the hair on my forearm. For a plate, I use a single 12×12 tile from a Big Box store.
Only comment would be to start with manual machines -once you have them mastered, then worry about CNC. I'm only 71 at this point, but I still have a lot of things left to master! Try to find even a HF mini-lathe and mill used, and get started. The sooner you start, the sooner you become experienced, Just a warning though - machining is just as addictive as wood working.
Ok, the leap from $1,000 to $2,500 is a big one. I certainly didn't make it at one time. It took me years. But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted. When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
My name is Marc Spagnuolo and welcome to my channel. I am a podcaster, video producer, author, and woodworking enthusiast. I have contributed articles and video content to FineWoodworking.com, Popular Woodworking Magazine and WOOD Magazine. Producing the Wood Whisperer is a great way for me to combine four of my passions: woodworking, technology, education, and humor. I believe that even the most complicated woodworking project is just a series of steps. My goal with this channel is to show you the tools and techniques you need to perform those steps.