Only comment would be to start with manual machines -once you have them mastered, then worry about CNC. I'm only 71 at this point, but I still have a lot of things left to master! Try to find even a HF mini-lathe and mill used, and get started. The sooner you start, the sooner you become experienced, Just a warning though - machining is just as addictive as wood working.

Another example is lathe tooling or metal gravers which are routinely polished on fine agate stones and these don’t chip or roll an edge unless abused. These are one of the times where a jig is a requirement for reproducible results and a couple degrees off the recommended angle can make a difference. For a wood work, a couple degrees either way won’t really be noticed.


You can create a beautiful coffee table by simple stacking logs together. Line the logs end up and create a circle whatever size you need. Then just tie them all together with rope or twine to keep your coffee table secure. You do need to make sure that the logs are the same height and you may want to sand the tops down just a bit to make them smooth.

These YouTube videos provide great woodworking information that contains both traditional and modern methods. Each instructional video contains woodworking how to techniques to improve a woodworkers’ skills and also methods for how to work safe in the shop. If you want entertainment, then watch the video once. If you want learn, watch the again. If you want to master techniques and improve your woodworking skills, watch and study the videos repeatedly.


We us the ReStore also– What great finds–sometimes things we were even looking for–my other favorite place is the second hand stores–many times they have give away bends that I have reclaimed out of–and we have a neighborhood swap–my favorite of all is the FREE CYCLE– its is a community of people that just give things away– OH MY GOSH–when I need to get rid of things after a yard sale its the best– someone always comes and reclaims my curdside giveaways–I love–it stays out of the dump and someelse is using something they may need badly– I have found tons of great things,wood,tirers, paint–ect.
Let's talk about a few strategies for building out your shop below retail price.  There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss.  First of all, not everyone lives in an area where these avenues exist.  Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand.  Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.

That's it. That's all you really need to begin woodworking. Over time you will add more tools to your collection, like chisels, drill bits, a sander and, more clamps; but for right now you should be able to get started on most beginner projects. Don't be afraid to look online for second- hand tools. Old drills and circular saws work well when given proper care. With some ingenuity you can figure out how to adapt most plans to the tools you have available. People have been making wooden items throughout human history, and they didn't need expensive planers, biscuit joiners or fancy jigs. Start learning the craft, see if you like it, and have fun.
Softwoods are often softer and more delicate woods in general, as the name would suggest, but aren’t necessarily always weaker than hardwoods. Although, they are generally less dense and not as durable as Hardwoods, which grow at a much slower rate than softwoods creating a denser and stronger grain in the wood. Softwoods come from coniferous (or gymnosperm) trees such as Cedar, Hemlock and Pine and lean towards a yellow to reddish tone by nature. Hardwoods come from angiosperm (seed producing) trees such as Oak, Cherry, Maple and Walnut and are generally darker toned woods. Softwoods tend to be less expensive than hardwoods, as they grow much more quickly and can be milled at a faster rate. While hardwoods are generally more expensive, the durability, strength and overall look is often worth the additional cost depending on your project needs.
Even the backside grinding shown in the single frame of the video shows the effects of hand held sharpening. There is a curve on the flat side of the blade! Starting to look like a spoon. It’s impossible to get a flat surface when using bones and tendons. This effect was exploited to make the first lens when done in glass. Telescope mirror grinders do it too using two different hardness of glass, if machine done it would be flat. If those “slate” tiles are flat they must be ground flat not baked. No need to check.

Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.
We've written about routers on the site before and my favorite is the Bosch 1617​.  It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table.  On top of that, it comes with a plunge base which makes it significantly easier to use handheld.  The package clocks in at ~$190.
Although we focus primarily on the use of wood in our work, CZ Woodworking also incorporates materials other than solid wood into our workshop. We work with metalworkers, glass companies, designers and artisans alike to bring various materials together to create custom pieces. Examples of additional materials we use are wrought iron, steel, glass, stone and more. By combining various mediums together, we are able to achieve the specific look that fits your needs best. Please contact us directly to inquire further.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
When I was just getting started with woodworking, I didn’t know anything about saws. The standard push saw was the only hand saw that I had any experience with. So naturally this was the type of saw I bought. It works fine for making cross cuts, and can even be used to rip, if you don’t have a table saw or circular saw. However, I quickly realized that I needed something for more precision cuts.
×