The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
The problems  that we least expect.  Five years ago i purchased a bicycle and discovered while riding that I had developed balance problems.  I ignored the problem and stopped riding the bicycle.During this period I built a workshop in my basement and stocked with the best handtools.  My lifelong dream was to be an anarchist!  In February 2012 I started having episodes of more severe balance problems which resulted in hospitalization and extended nursing home rehabilitationl for six months. The diagnoses is Parkinson Disease which causes muscles to react to unwanted brain signals.  Needless to say the therapist ordered "no woodworking" period" because of the hazards associated with machines and sharp tools.  I presented my case that I did only handwork with hand tools.  The therapist answer was "NO!".  Now I'm confined to using a walker or wheel chair and reading how you all are enjoying the smell of sawdust.
About Youtuber On this channel I will try to share my passion for wood and the skills and experience gained in the furniture carpentry business for almost 30 years. I will try to help solve the problems caused by the processing of wood and other furniture materials. When designing and fabricating furniture as well as I will try to tell you how to run your own business.

Just how small?  Will you have an extra bedroom for your shop or will you be doing woodworking in your living room?  Do you have to put the projects and tools away every time you want to entertain or will you leave everything set up all the time?  A while back FWW had a video tour of a shop in Japan that was smaller than small.  I'll try to find it and get back.  Found it...  shows what can be done in a small space but this shop was not on a small budget so no help there.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post. 

Our Woodworking Tool index (LEFT) includes a listing of all our Woodworking Tools and materials. Woodworking Hand Tools are one of our passions and we sell the very best hand tool brands in production today. Selecting the best woodworking tools for your woodworking shop and individual specialities can be overwhelming if you don't know the facts. At Highland Woodworking we not only carry a great selection of top rated tools but we also provide top notch information on woodworking tools and techniques like our starter woodworking tool list for beginners. We've been offering fine woodworking tools and education since 1978, keeping woodworkers informed about the best woodworking tools, tips & techniques along the way. Purchases are backed by Highland Woodworking's 60-day money back guarantee, so you can shop us with confidence for high quality woodworking tools.


If you are just getting started in woodworking and want to know what tools you’ll need to set up shop, you’ll want to download this free PDF from Popular Woodworking. We have put together a complete list of basic woodworking tools to kick-start your new hobby. In this free download, you’ll get our recommendations for the best hand and power tools for beginners. Buy these tools and you’ll have everything you need to make great woodworking projects.
The first word that comes to mind for describing Jay’s work: Accessible. Even if you are brand-new to woodworking and don’t have many tools, you can follow many of Jay’s projects. It’s not just the choice of tools and techniques, but also his straightforward and friendly presentation style. Here is a video that’ll be handy for anyone just shopping for a new kitchen:
About Youtuber My name is Andrei. I live in Russia and run my small business. Woodworking is my passion. I am the only woodworker in the shop. It is my full time job. I make only end grain cutting boards. I've been making end grain cutting boards for years. Sometimes I make end grain chessboards, end grain jewelry boxes, etc. Also I prepare woodworking plans.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
2. Just the basics—I’ve used a compound miter saw, circular saw, jigsaw, band saw, router, table saw, drill, finishing sander, belt sander, Dremel, oscillating multi-tool, bar clamps, and a Shop-Vac. I haven’t used a planer, jointer, or lathe. I’ve never owned a table saw but have used a circular saw or improvised with a router for a few long cuts.
About Youtuber Here you will find everything from money saving tips, woodworking projects, jigs and completely wild contraptions. I have been building and designing since I was old enough to swing a hammer. With a mind for out of the box thinking and an unusual mix of artfull design and engineering interest, you never know whats going to happen next.
Screwdrivers are another must-have in the woodworker’s set of hand tools. Not only will you need Phillips and slot, or flathead screwdrivers, you’ll need star drivers and Torx drivers, too. A quality construction is vital to a good set of screwdrivers. So many of them are made out of soft metal, and the first time you put any “oomph” behind them, they strip out, becoming absolutely useless.

For under $20 I am very impressed with the Bad Blade Carver by Kwik Tool.  Mounted in a 4.5″ grinder, it removes a ton of material quickly yet allows a fair amount of control.  The disk has only 6 teeth so the carver is mainly a solid disk with very few teeth to bite and create kick-back or dig-in. I found I had the best control when engaging the blade between 12 o’clock (top of the grinder) and 3 o’clock. When in that range it was not overly aggressive and left me in control.
Well there it is, my top 5 list of the best beginner woodworking tools. Let me know your thoughts or some of your favorite tools for each category. Of course this isn’t an all-encompassing list, there are all of the little extras like tape measure, square, clamps, glue, etc. To see what I use for all of these options check out the complete list of tools from my shop.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.

Maple comes in two varieties: hard and soft. Both varieties are harder than a vast majority of other woods and are moderately priced. Because of their fine, straight grain, both varieties are more stable than many other woods and perfect for tabletops. Exotic varieties of Maple exist – such as Curly, Tiger and Birds-Eye Maple – which are used in fine woodworking for an unparalleled finish, with grain patterns that are extremely unique and distinct but come at a higher cost.

In addition to the type of finish you want, the location of the final installation should be considered when choosing a hardwood species. While it won't have as much bearing on furniture pieces to be used indoors, you may want to consider some more moisture-resistant species (such as cypress or the ever-increasingly endangered teak) for outdoor projects. Again, your local woodworking supplier will be able to help with this decision if you are unsure about what species might work well for your particular application and climate.
For me, I watch Craigslist, and hit auctions. My g/f scored me a huge load of pallets (free wood is good wood, especially when projects made from it generate $$$), and I work in a high end window & door company, so the scrap bin gets raided quite often. I made a deal with myself to only buy what I can pay for from what the shop makes. This includes (at times) going without a needed tool as I was waiting for a better one because I had sold what I once had for more than I paid for it. Just like flipping houses, on a much smaller scale. Right place, right time.
Not many YouTube woodworking channels are run by guys who also happen to have PhD’s in medicinal chemistry, but this one is. Brian Grella’s channel offers a mix between more atmospheric videos that aren’t heavy on explanations (as the one shown above), and ones that are firmly in how-to territory, like this one for making a beautiful wooden bowl using nothing but a router and a drill press (no lathe required):
For me, I watch Craigslist, and hit auctions. My g/f scored me a huge load of pallets (free wood is good wood, especially when projects made from it generate $$$), and I work in a high end window & door company, so the scrap bin gets raided quite often. I made a deal with myself to only buy what I can pay for from what the shop makes. This includes (at times) going without a needed tool as I was waiting for a better one because I had sold what I once had for more than I paid for it. Just like flipping houses, on a much smaller scale. Right place, right time.
You can find a project for just about every room in your home. Table scape trays make perfect platforms for dining room decoration. Wooden plaques offer a blank slate for any saying or picture you want. If you want a unique table, we’ve got a few options to consider. Headboards and benches can give your bedroom a real transformation. You can find anything you want among these DIY wood craft projects.

Whatever your dream for a rustic look, you are sure to find something in this collection that will help you along. Many of these projects are so easy to do and you can complete them in less than a day. Some make wonderful gifts as well so if you know someone else who just loves the country, rustic look, make them something to brighten their own décor. The projects use all sorts of materials, many of which are really inexpensive or even cheap in some cases.

Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
Second, it is easier to learn to use hand tools on a solid bench than on a Workmate or some other modern clamping sawhorse.  The bench doesn't have to be expensive or large.  A 20" by 5' top will get you started.  Look at Chris Schwarz's second book on Workbenches "The Workbench Design Book" for ideas.  If you are a good scrounger you can recycle framing lumber from building teardowns to build a good bench for next to nothing.  A vise screw to make a leg vise is less than $60.
The second big tool you need is a saw. There are many types of saws, and this can be the trickiest part of setting up a shop on a budget. As a beginner, you'll likely be using woodworking books, magazines and websites for instruction and inspiration. Unfortunately, most of these sources consider a table saw a beginner tool. For those of us on a budget, or with little space, a table saw may not be an option. They cost several hundred dollars to start, and take up several square feet of floor space. Instead, look for a good circular saw that allows you to adjust the depth and angle of cut. It's also nice to have a laser to help guide the cuts. You can get a decent circular saw for around $100.
That just reminded me of a FWW piece many years ago that had me rolling on the floor.  Craftsman had built a large piece being delivered to an apartment on the top floor.  Couldn't get it on the elevator so they got controll of the elevator and ran the top of it to be even with the floor, loaded the piece on the top of the car and rode with it inside the shaft while balancing it and keeping it from hitting the shaft walls.  At some point in the trip up they lost control of the elevator and it started making trips up and down to other floors.  I'll see if I can find it.
The circular saw is pretty much the first tool I grab for any project. You can use it for both rough cutting your lumber to get started on a project or making finish cuts before final assembly of your project. You can use it to make half lap joints and a variety of other joinery methods. While a table saw or stationary miter saw might make a certain task easier, it is hard to beat the cost, portability, and versatility of a circular saw. While most of these come with a blade, here is a good all-around blade that I use. 
×