This unique approach to woodworking was expressed by George Nakashima’s work throughout the mid-20th century. He became known for leaving the natural, or live edge of the wood in tact as part of the finished piece. The profile of this live edge reflects the curvatures and unique textures of the tree’s exterior silhouette, assuring that no two pieces are ever the same. The use of this wood creates a bold, artistic and natural feel that is an extremely interesting way of obtaining that “wow factor” in a piece.
Cutting thick, rough, warped hardwood can be cumbersome and dangerous. To provide some control over this process, I built a chop-saw station with wings that extend to support long boards. Again, anytime you make something that consumes shop space, make a shelf underneath to gain storage. The chop saw sits in a recess so that the deck of the saw is at the same height as the workstation deck.
Matthias Wandel comes out with some amazing modifications for tools and techniques. This one however is incredibly simple and only requires a few scraps of wood and a pair of clamps to turn a simple circular saw into a custom width dado maker. You can spend a lot on special dado blades for table saws or router with a straight bit and some guides, but this method is simpler and the results are very close to the same. Very little is sacrificed by using this frugal dado making method.
Flea markets and swap meets are great sources of old tools, but unless you are able to rehab and sharpen them, they aren't going to do you much good. You can always find lots of chisels and planes at these places, and they can be brought back to life. I wouldn't waste my time on any saws though, unless they are relatively rust-free. If a saw is rusty, you will have to re-file and re-set the teeth, which requires a good deal of expertise and some specialized tools.
Arbortech Turbo Plane – The turbo plane is more than 7 times the cost of the Bad Blade Carver, however The turbo plane is kind of a more refined animal. It probably isn’t fair to compare the two. The Turbo Plane leaves a better finish and can be used in a different way, but for bulk removal and heavy shaping, I think the Bad Blade Carver wins. If you want the scalloped and smooth surface, then the Turbo Plane wins.
I set an initial budget of $10,000 to build the shop – everything from studs and drywall to hand tools and machinery. The final number was over by $1,000, but I’m still very happy with the result. The shop is now my haven, with a good sound system and good lighting. Every time I go back into the shop, it is exactly the way I left it, because it is my shop!
Those two tools comprise the most basic power tools you need to start woodworking. In addition, you'll need some hand tools. A hammer is an obvious necessity, and can be bought cheaply. A tape measure is a must- have for marking out lengths. A ruler or straight edge is needed to turn your measurements into straight lines for cutting, and can be clamped to a work piece to use as a saw guide. Speaking of clamps, they are important for joining pieces together for gluing, screwing or nailing. Most woodworkers have a lot of them, and you'll never have as many as you need. For now, just buy a few 6-inch and 12-inch clamps and add more as you need them.
In fact when I first met her she had walked away from a construction job building three story apartment housing. One day they were working on the third floor with a fairly high wind , and speaking of plywood, there were stacks of plywood up there and she tried to tell the guys they needed to secure the plywood or they would start to take off like playing cards.
She came back to the mainland when her family was building a sky scraper in Denver. ( Well about as tall as any of the other down town high rises.) I got to tour it while it was being built. Very cool ! So hanging around this crew of a family she picked up quite a lot. The wife of her brother, the iron worker and pro chef, was an iron worker as well. The first lady ironworker I had ever met and I grew up around construction workers some what. Hard core people ( bound to rub off ).
Then there are the “practical” woodworkers that enjoy weekend projects and things that don’t require a ton of expensive tools, time, and expertise (HELLO, THAT’S ME). I will be in the latter category. Sure, you can invest in hand tools, but in the words of one of my favorite internet sensations, “ain’t nobody got time fo that.” Let’s be practical here.
So I am curious about what the best choices in woodworking tools would be for someone who is just beginning to develop the skills involved with the craft. Funds would be limited and at least for me, I have a strong preference for non-electric tools when possible. Not only what would be the best tools to start a collection with, but also what would be a good way to obtain them aside from ebay, pawn shops and antique shops?
Hardwoods come from deciduous, or broad-leaved trees, as opposed to softwoods, that are harvested from from evergreens. In general, the lumber derived from hardwood species are typically harder than softwoods, although there are exceptions (balsa wood is very light and soft, but is considered a hardwood). Most hardwood tree species lose their leaves in winter, and generally offer a much wider variety of colors and textures than softwoods. Typically, stock from hardwood species are a lot more expensive than those from softwoods.
If you are an advanced woodworker then you might want to check out the Wood Whisperer channel. It has advanced projects broken down to the details in multi-part series and also technique videos. Mark Spagnuolo has been creating DIY woodworking videos on the channel since 2006, so there is a lot of content to scratch the itch of any woodworking enthusiast.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
I can't really give a great answer to your question - I'm still learning how to deal with woodworking on a limited budget myself, but I'm getting there. It's not always easy, but when I want something I can't afford, I am starting to remind myself more and more that someday my day will come when hopefully there will be more room in the budget for my woodworking hobby. I'm also hoping to start selling the occasional item within the next year to help bring in some extra money for woodworking related expenses.
We've written about routers on the site before and my favorite is the Bosch 1617. It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table. On top of that, it comes with a plunge base which makes it significantly easier to use handheld. The package clocks in at ~$190.
At $300, the saw is expensive, but it is one of the more affordable saws that offer a 12 inch blade and a double bevel. The double bevel allows you to adjust both the angle at which the blade cuts into the wood and the tilt of the blade relative to the workpiece. Having control over both angles allows much easier cuts of trims and moldings. It's one of those features that you won't use with every project - but when you do need it, you'll be glad you have it
If you'd like to learn more about the differences between hardwood species, I can think of no better resource than R. Bruce Hoadley's 1980 masterpiece, Understanding Wood: A Craftsman's Guide to Wood Technology. Not only does Hoadley detail nearly every species used for woodworking, he does an exceptional job at describing how to prepare, work with and finish these hardwoods. This is an industry-standard resource, one that I'd highly recommend to every woodworker.