Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.
The solution to potentially wedged boards on a jointer is to add a planer to the mix. A planer has a flat surface with a cutting edge that is exactly 180 degrees to the surface. This allows you to position the jointed edge flat on the planers surface and make a cut to the opposite side of the board that is perfectly square. As an added bonus, the planer allows you incredible control over the thickness of the boards you're planing.
However, if you want to stain or clear-coat the project, you'll have a number of choices to look through. Since your local home center megamart will probably only carry a couple of hardwood species (poplar and red oak are common) spend time at a fine wood supplier and look through the vareties available. They should be able to help you determine how each species will look when finished, which will go a long way toward refining your decision.
Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps.
While there are certainly tools beyond this list that would make certain tasks easier, I feel confident that you can build pretty much anything you could possible want using this beginner woodworking tool set. Everything on this list is also purposefully portable and does not take up much space at all. The goal here was to compile a list of the best beginner tools that would allow you to build almost anything, anywhere, and only take up a small cabinet in your house or garage.
These YouTube videos provide great woodworking information that contains both traditional and modern methods. Each instructional video contains woodworking how to techniques to improve a woodworkers’ skills and also methods for how to work safe in the shop. If you want entertainment, then watch the video once. If you want learn, watch the again. If you want to master techniques and improve your woodworking skills, watch and study the videos repeatedly.
Non-Standard Miter Slots - This one is a downer. One of the primary advantages of having a table saw is access to jigs that expand the saws functionality. This is a major issue if you plan on buying after market jigs. Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list. Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.
A personal favorite of Chris’s, this wood is the ideal choice for woodworking pieces that want to showcase beautiful grain and an excellent finish. The naturally wavy grain of Black Walnut creates a look that is artistic and abstract, with a density that also gives weight and strength to the piece. Black Walnut stains wonderfully, but is almost best when the natural elements are emphasized with an oil finish only – and it should never, ever, be painted!
Flea markets and swap meets are great sources of old tools, but unless you are able to rehab and sharpen them, they aren't going to do you much good. You can always find lots of chisels and planes at these places, and they can be brought back to life. I wouldn't waste my time on any saws though, unless they are relatively rust-free. If a saw is rusty, you will have to re-file and re-set the teeth, which requires a good deal of expertise and some specialized tools.
I use a 9″ x 12″ Chinese grade B surface plate and wet the back of the carborundum “sandpaper” to hold it in place. Obviously not the “budget” version, but I have the surface plate for other purposes. At about $17 from ENCO it wasn’t very expensive. And it *really* is flat to better than 0.001″. So the thickness of the paper is the biggest error. I also have a good assortment of Arkansas and other types of stones, though none of the Japanese waterstones. I generally don’t use the surface plate unless the edge is really bad e.g. an abused tool picked up at a yard sale.
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
Many beginners trying to get started in woodworking take one look at their budget and worry how they can afford to buy a whole shop full of power tools to get started. Fortunately, one doesn't have to spend a fortune to get started. There are really only seven woodworking tools that I would recommend any beginning woodworker have on hand from the start, and most are relatively inexpensive. However, with these seven tools, a beginner can tackle quite a number of projects.
Frank’s work is visually arresting. This is not necessarily a channel you’re going to learn from, if you’re a novice woodworker or just getting into the field. The main reason to subscribe to Frank’s channel is how gorgeous his work is. The pieces he makes are always artfully conceived, even if it’s just a simple bookcase or a bench. Add to that his killer stop-motion and filmmaking skills, and you get a YouTube channel you can share with anyone, even if they think they’re not remotely interested in the craft.
All in all, for whatever reason it is that you enjoy woodworking, then you always need to follow that passion. There is always going to be obstacles to overcome, whether that be not enough money to buy your tools, or space to put those tools, or time to enjoy woodworking. That is something that every person has to overcome. Everybody has there own unique obstacles.
Rob Cosman and Paul Sellers. Rob is damn near a genius when it comes to woodworking. He routinely comes up with methods and tools that sort of change the way we all do things in the shop. The guy is also an amazing instructor. Paul Sellers is also an amazing instructor. These are the kinds of guys that all the rest on your list learned how to woodwork from!
We made the decision for my wife to be a stay at home mom - it was a decision we both felt was a good one before we ever even discussed it. Being a single income family does sometimes have financial drawbacks, but the blessings of my wife being a stay at home mom are blessings that money can't buy. Eventually, when our son (and any future children we may have) are in grade school, my wife will look at finding a job. She's also looking at the possibility of starting to do in-home daycare for 2 or 3 children in our home, which would bring in some extra money.